Halfish 24



The Cygnus Halfish 24 is designed as a shallow draught, multi-purpose, costal fishing vessel and workboat to operate from tidal harbours and beaches with a crew of one or two and for all year round use in the very worse conditions. The design is traditional in nature and attractive in appearance. Hydraulic machinery can be installed to carry out a range of fishing operations such as creeling, long lining, gill netting and trawling.

The light displacement and hull shape gives good fuel efficiency from low horsepower diesel engines. Traditional proven fishing boat design with attractively flared bows and sheer line. Well or self-draining deck options. GRP wheelhouses can be open or enclosed. GRP gunwales completed with iroko fendering or full hardwood.

Hull, wheelhouse and gunwales are available in kit for home completion Classification Society certification possible. Only the best marine quality gel coats, resin and fibreglass are used throughout. Fit out is to a heavy and robust standard to withstand the rigours of prolonged professional and commercial use.

Technical data

Length Overall 7.52 m 24 ft
Beam 2.90 m 9.5 ft
Draft 0.93 m 3.05 ft
Air draft (Waterline to top of mast) 3.00 m 9.8 ft
Displacement 4.0 tons
Engine recommendation (Single) 40 - 86 HP / 29.83 – 59.66 KW
Top Speed Range 13 km/h – 14.8 km/h 7 - 8 knots
Fuel consumption (7.5 knots) Ca. 1.33 l/nm 0.29 Gal/nm
Maximum cruising range/time Ca. 187 nm – 300 nm 24 hrs – 39 hrs
Certification SFIA, BIM, MCA  
Fuel tank 250 – 400 litres 50 – 88 Gallons
Water Capacity 25 litres 5.5 Gallons
Battery 2 x 120 AH - 12 V/24 V



Speed, planning hull.

Large flush working deck

Solid and high quality materials

As per customer requirements

Custom made fishing gear

Basic package

Basic package


  • Heavy-duty displacement single shaft drive Cygnus Halfish 24 hull with colour of customer’s choice, contrasting stripe above the water line and 2 layers of anti fouling.
  • Bilge keels
  • Stainless steel rudder and support skeg with bearing connected with hydraulic steering system.
  • Stainless steel propeller shaft with matching flexible coupling driving a bronze three bladed propeller. GRP glassed-in stern tube with inboard packing sealing gland.
  • Wooden fendering on gunwales. Finished with varnish or high gloss impregnating oil.
  • Fore deck and Halfish wheelhouse in white Gel coat bonded to hull.
  • Standard Halfish flush self-draining deck with full size deck hatch over engine and 1m x 1m hatch over a forward hold. Engine and hold hatch moulded in GRP, hinged on the outboard sides with hold open stay or equivalent. Draining through drains in hatch surround
  • troughs and scuppers through bulwarks. Deck finished in light grey non-slip deck gel. 
  • Aluminium framed toughened clear glass windows.
  • Sliding GRP wheelhouse door with aluminium framed toughened clear glass window.
  • GRP rooftop overhang in hull colour and spray deflector at aft of wheelhouse.
  • Two disc anodes fitted to rudder and 2 x large hull anode fitted and wired as necessary
  • Name of vessel on front of wheelhouse and on the stern of the vessel


  • Forward cabin with two shelves for storage to starboard side. Floor to be painted in light grey anti skid paint. Bulkheads and overhead gel flow coated.
  • Wheelhouse with small chart table to portside and instrument/navigation console to starboard side. Forward port side opening giving access to forward cabin. 
  • Generally all bulkheads flush coated white. Ceiling in white marine plywood. Lights flush mounted in ceiling.
  • Steering position with instruments to starboard side.
  • Engine instrumentation and controls mounted in wheelhouse
  • Storage compartment below wheelhouse floor wit watertight hatch.


  • Engine: Perkins Sabre M92B with Newage PRM500D reverse marine gearbox. Marine Medium Duty Commercial Rating 2
  • Engine with flexible mount supports, Fresh water heat exchanger cooled engine with gear driven self priming raw water and fresh water pumps or keel cooling adaption. Air intake filter. High inclination engine sump with sump drain pump. Inverted spin-on element lube oil filter. Transmission oil cooler. Totally enclosed engine breather. High mounted single element fuel filter. Manual control adaption parts. Alarm switches and warning siren.
  • Single station power and gear controls at the helmsman position.

Fuel and Cooling System

  • Engine cooling system via through hull sea cock and quality raw water filter system
  • Freshwater cooled exhaust manifold, intake manifold and heat exchanger. Elbow connected to marine exhaust hose with good run down and transom fitting with non-return flap in stainless steel. Hose to be double clipped. 
  • Engine room ventilation ducts under gunwale
  • Single 250lt Aluminium powder coated Fuel tank complete with filler through deck connected to engine via quality pre fuel filter system. Vents in flexible fuel hose with swan neck and anti-flash gauze in stainless steel.
  • Tank gauge at helm
  • Remote fuel shut off valve at the fuel tank
  • Fuel supply fitted with water separator/filters.

Electrical Fittings

  • Electrics supplied by two heavy-duty 12-volt batteries via heavy duty Vetus isolation switch wired to 5-gang switch panel in wheelhouse via split charge unit. Battery charging by standard engine mounted machine sensed alternator as supplied by engine maker.
  • Main DC switchboards fitted into the wheelhouse in/or near the console.
  • Batteries installed in topped boxes adjacent to engine.
  • Electrical Circuits:
    • Compass light
    • Anchor light
    • Navigation lights, one sat port and starboard mounted on wheelhouse
    • Navigation light, top, stern and anchor light mounted in stainless steel radar mast (All according to IMO)
    • Wheelhouse interior down lights x 2 and 1 red light at helm
    • Instrument lights
    • Engine room and hold light. Heavy duty x 2
    • Fore cabin lights x 1 down lights on ceiling
    • 1 windscreen wiper at centre forward window
    • Electric bilge pumps x 1
    • Bilge alarm x 1
    • Horn with console switch
    • Spare ways in MCB panel
    • Cathodic protection anodes one to be wired to engine and other systems

Stainless Steel Fittings

  • 3 Strong bollards, one on fore deck bolted through superstructure and two aft at transom 
  • Heavy duty Cygnus custom made bow roller 
  • Stainless steel mast
  • Fog horn
  • Filling plugs and vents for fuel and water tanks.
  • Railings around cockpit

Other Fittings

  • Emergency bilge pump nr 1: Single Jabsco water puppy bilge pump fitted in engine room controlled from wheelhouse through an on/off/auto switch
  • Emergency manual bilge pump serving engine room and hold
  • Bilge alarm in engine compartment
  • Navigation lights mounted on wheelhouse and radar mast.
  • Galvanised anchor 15 Kg with swivel and 50m three strand 14 mm nylon rope
  • 1 Portable fire extinguishers
  • Safety equipment including lifebuoy, 2 floating smoke signals, 3 hand parachute signals and a first aid kit
  • Basic toolbox and spares
  • Flag post on transom
  • Identification plate and owners manual

Navigation Equipment

  • Magnetic compass Offshore 95, compensated and with deviation card.
  • Radar reflector




Coming soon